Preventing rust and brake corrosion on a stored classic car
Wash and dry a stored classic, including the underside. Control humidity, and plan for rotor rust, the parking brake, and brake fluid.
How do I prevent rust and brake corrosion on a stored classic car?
Short answer
Wash and dry the car before it stays, including the underside where road salt collects. Leave the parking brake off the way the storage instructions cited below describe, and block the wheels. Cast-iron brake rotors can show surface rust while a car sits. Brake fluid is tested by federal rule with water in it, which is why the fluid belongs in the storage check. The room and the cover are car covers and moisture control. Oil, coolant, and the brake-fluid rating on the cap are oil and fluids before storage.
Published Updated as of
Wash and dry the car before it stays, including the underside where road salt collects. Leave the parking brake off the way the storage instructions cited below describe, and block the wheels. Cast-iron brake rotors can show surface rust while a car sits. Brake fluid is tested by federal rule with water in it, which is why the fluid belongs in the storage check.
The room and the cover are car covers and moisture control. Oil, coolant, and the brake-fluid rating on the cap are oil and fluids before storage. The rest of the layup order is how to store a classic long term. The sentences below are from the owner-manual page, the service bulletins, the federal standard, and the extension and highway publications linked in each section. Follow the manual for the car you have when it names a step.
Before the car stays parked
- Wash off dirt and road salt, including the underside, then dry the car completely.
- Repair paint chips the way the manual or a body shop describes, so bare metal is not left open.
- Use a breathable cover only after the car is dry, or leave it uncovered in a clean, dry room.
- Leave the parking brake off, put the transmission in Park or the gear the manual names, and block the wheels.
- Read the manual before you disable an electric parking brake's automatic setting.
- Check brake fluid against the rating on the cap. The fluid guide is the place for a flush.
- On the first roll, confirm the pedal feel before traffic. Heavy rotor rust is a shop question.
Wash and dry the car, including the underside
American Honda's storage article (opens in a new tab) is the company's minimum recommendation for conventionally powered Honda vehicles stored more than one month. It says to wash and dry the exterior completely, and to clean the interior so the carpeting and floor mats are completely dry. It also says that if there are paint chips, have them repaired. The article tells Honda owners who plan to store a vehicle more than six months to consult an authorized Honda dealer. That six-month note is Honda's, for Honda vehicles.
Salt is the part a hose is meant to remove before a car sits. A manual on corrosion of highway-agency equipment (opens in a new tab), published from a pooled-fund project through the Minnesota Department of Transportation, says the deicers highway agencies use are mainly chloride-based salts. It lists steel frames, brake lines, and cast-iron brake drums and disks among the metals subject to those deicers. It says crevice corrosion and poultice corrosion typically occur where dirt and moisture are trapped, between adjacent pieces of metal, under gaskets and at fasteners, or on the surface of components, and that snow and ice control chemicals increase the conductivity of that trapped moisture. The manual is written for department of transportation equipment, not for collector cars. Its wash list is still specific: concentrate on frame rails, brake components, the underneath of the chassis, and other areas that collect material. It says to wash preferably with hot water and then dry quickly. It says preferably not to use a pressure washer, because water can be forced into areas and cannot escape, which leads to corrosion. The daily wash in that manual is a fleet practice for trucks that carry deicer. It is not a schedule this page assigns to a classic.
A rinse does not restore steel that is already pitted. A Federal Highway Administration report on soluble salts on steel (opens in a new tab) is about bridge steel, and it says deicing salts are a significant source of soluble salts on that steel. It also says that although most of the salts are soluble in water, they cannot be easily removed by washing or abrasive blasting, and that salts may sit in pits and crevices within or under rust. Wash the car so this season's salt is not stored against the metal. Do not treat the wash as a repair of rust that is already under the paint.
Two extension pages describe the same clean-and-dry habit for farm and yard equipment. Louisiana State University AgCenter (opens in a new tab) says dirt, dust, and crop residue can be corrosive when mixed with grease and oil, that rain can be damaging, and that washing after use and putting a machine away clean helps preserve it. It says storing machinery in a shed keeps it clean and dry, and that repainting scratches and paint chips helps prevent rust in those spots. Montana State University Extension (opens in a new tab) says dirt, chaff, and fertilizer residues hold moisture and cause corrosion, and that washing before storage lessens that risk, including under shields and in other places residue builds up. Neither page is a car manual. Both are a reason to put the car away clean.
Humidity, a wet car, and the cover
Montana State University Extension says freeze-thaw cycles in an unheated shed or in outdoor storage create condensation, leading to rust in fuel tanks and engine components. It says indoor storage in a machine shed or barn is best, and that an outdoor cover should allow ventilation, with the equipment on well-drained ground. Honda's storage article says to cover the vehicle with a breathable cover made from a porous material such as cotton, and that non-porous material, such as plastic sheeting, can damage the paint. Put that cover on only after the exterior and the cabin are dry. A cover on a car that is still wet is the problem the cover guide describes.
The highway-equipment manual lists humidity among the climatic conditions that influenced corrosion rates of specimens mounted on winter maintenance equipment, along with how often the equipment was washed. A garage that sweats, or a cover that stays damp on the inside, is the room problem. How to judge that room, a dehumidifier, a desiccant, and a breathable cover is car covers and moisture control. Dry the car after the wash, and do not close it up wet.
Leave the parking brake off and block the wheels
Honda's storage article says to leave the parking brake off, put the transmission in Reverse for a manual or Park for an automatic, and block the rear wheels so the car cannot slip or move. Toyota service bulletin T-SB-0036-22 (opens in a new tab), dated April 8, 2022, and hosted in NHTSA's service-bulletin library, is written for dealer inventory of listed 2023 Toyota models, not as an owner schedule for every classic. In its parking procedure it says not to apply the parking brake. For a vehicle with an electronic parking brake, it says to make sure the brake does not engage and that the automatic function is disabled, and it points to the owner's manual for that step.
Those two publications are the instruction this page is using: parking brake off, car held by the transmission position they name and by blocked wheels. If the car will not stay put that way, fix the slope or the chocks before you rely on a brake the storage articles say to leave off. Read the manual if it describes a different hold for that transmission or for an electric parking brake. Honda's article also tells the owner, when the car comes out, to check the brake pedal for normal feel, both height and firmness, before shifting. That check is in the spring startup guide.
Surface rust on brake rotors
Toyota's bulletin says the brake rotors are made of cast iron and may show a gradual build-up of surface rust during long-term storage. It says to drive the vehicle and use the brakes normally at least once every eight weeks, to help prevent severe rust build-up and unwanted brake vibration. The bulletin includes a table of stops for dealer staff clearing that rust: 5 stops from 60 mph, 10 from 40 mph, 20 from 30 mph, and 30 from 20 mph, chosen from the speed limits and traffic where the car is driven. It shows slight rust as easier to remove by braking and severe rust as harder. It says rotor resurfacing may be required if the rust was severe and caused excessive rotor thickness variation. It also says that if vehicles in the storage area are exposed to a sea breeze or significant precipitation, rust may occur, and that rust which is found should be removed and treated with a rust inhibitor. This page does not name a product.
General Motors service bulletin 09-00-89-002R (opens in a new tab), revised May 2020 for 2011 through 2021 GM passenger cars and trucks and also hosted by NHTSA, is a dealer-inventory bulletin. It says braking systems tend to be self-cleaning while vehicles are in use, which prevents a build-up of corrosion on the rotor surfaces. It says vehicles should be moved and the brakes applied every 30 days for that practice to remain effective. It says more extensive corrosion can cause pulsation from thickness variation, usually when a vehicle is parked for a long time in humid conditions and the braking surface under the pads corrodes at a different rate from the rest of the rotor. If that pulsation is already there, the bulletin describes a clean-up of 10 to 15 moderate stops from 35 to 40 mph, with cooling time between stops.
The eight-week Toyota interval and the 30-day GM interval are not one rule, and both bulletins are about new vehicles in dealer inventory. A classic with drum brakes is outside the rotor description those bulletins give. If your manual names a storage drive, follow the manual. If it is silent, the shared point is that those manufacturers remove light rotor rust by driving and using the brakes, on the vehicles the bulletins cover. The stop counts above are their dealer procedures. They are not a drill this page assigns to a car whose pedal you have not checked. A soft pedal, a vibration, or rust the bulletin would call severe is a reason to stop and use a shop. A few minutes of cold idle does not apply the brakes. That distinction is whether to start a stored classic periodically.
Brake fluid is evaluated with water in it
Federal Motor Vehicle Safety Standard 116 (opens in a new tab) sets requirements for fluid used in motor-vehicle hydraulic brake systems. Its purpose is to reduce brake-system failures that can follow from improper or contaminated fluid. The standard requires a dry equilibrium reflux boiling point and a wet one, measured after the fluid is humidified. For the grades it lists in that boiling-point section, the dry minimum is 205 °C (401 °F) for DOT 3 and 230 °C (446 °F) for DOT 4. The wet minimum is 140 °C (284 °F) for DOT 3 and 155 °C (311 °F) for DOT 4. The container rules also tell a label to distinguish DOT 5 silicone base fluid from DOT 5.1 non-silicone base fluid.
The water-tolerance procedure dilutes brake fluid, except DOT 5 silicone-base fluid, with 3.5 percent water. The text mixes 3.5 ml of distilled water with 100 ml of fluid, plus or minus the tolerances printed there, then holds it cold and warm and checks for sludge, crystals, and separation. DOT 5 silicone-base fluid is humidified instead of mixed with that 3.5 percent water. The corrosion procedure is separate. For fluid other than DOT 5 silicone-base, it mixes 760 ml of fluid with 40 ml of distilled water and holds metal strips, including cast iron, in that water-wet fluid at 100 °C (212 °F) for 120 hours. The strips are not allowed to pit or etch to an extent you can see without magnification. The standard is a lab rule for the fluid in the bottle. It does not print a storage calendar or a percent of water a parked car will gain.
Match the rating on the reservoir cap, and do not mix silicone-base fluid with the other grades. Level, color, and whether the fluid is due are the checks in the oil and fluids guide. Use the interval in the manual for the car. If the manual is silent, ask a shop that knows the system. This page will not invent a mileage or a month count.
The first time you roll the car
Look under the car for fresh rust you did not see at layup, especially along the frame, the brake lines, and the floors, which are the areas the highway-equipment manual treats as places deicer and damp dirt collect. Confirm the parking brake releases and the car rolls in a clear bay. Honda's coming-out list says to check the pedal for normal height and firmness before you shift. Then use the spring startup guide before traffic.
Light surface rust on a cast-iron rotor is the condition Toyota's bulletin describes as possible after storage, and as something normal braking is meant to clear on the cars that bulletin covers. Vibration after that, or rust that braking does not clear, is the point at which Toyota's bulletin says to find the cause and, if thickness varies, to consider resurfacing. That is a measurement for a shop. It is not a guess from the color of the rust.
Frequently asked questions
Should I wash a classic before storage?
Yes. Honda's storage article says to wash and dry the exterior completely. The highway-equipment manual and the extension pages say dirt, salt, and residue hold moisture and feed corrosion, including on the underside and brake parts. Dry the car before it is closed up or covered.
Should the parking brake stay on while the car is stored?
Honda's storage article and Toyota's dealer storage bulletin both say to leave the parking brake off. Honda says to block the rear wheels and leave the transmission in Park or Reverse. Follow the manual for an electric parking brake.
Is surface rust on the rotors after storage a failed brake?
Toyota's storage bulletin says cast-iron rotors may build surface rust in long storage, and that normal braking clears light rust on the vehicles it covers. Severe rust, a soft pedal, or a pulsation is a reason to have the brakes checked. The stop counts in that bulletin are a dealer procedure, not a drill for every classic.
Does the brake-fluid standard say the fluid contains water?
FMVSS 116 tests the fluid after humidification for a wet boiling point, and, except for DOT 5 silicone-base fluid, mixes in 3.5 percent water for the water-tolerance test. A separate corrosion test soaks cast iron and other metals in water-wet fluid. The standard does not give a storage interval. Follow the manual, and the fluid guide, for a change.
Will a plastic cover stop rust?
Honda's storage article says to use a breathable cover made from a porous material such as cotton, and that non-porous material such as plastic sheeting can damage the paint. Cover a car only after it is dry. The cover and moisture guide is how that choice works indoors and outside.
Bottom line
Put the car away clean and dry, including the underside where salt sits, and keep that moisture from staying in the room or under a plastic cover. Leave the parking brake off, block the wheels, and follow the manual on an electric parking brake.
Light rotor rust is a storage condition two manufacturer bulletins describe, and they clear it by driving and braking, on the vehicles those bulletins cover. Brake fluid is a federal standard that tests water in the fluid. The cap, the manual, and the fluid guide decide what goes in the reservoir.
Related guides
All guides →Battery Maintenance for Stored Classic Cars
How to keep your battery healthy through months of inactivity
Tire Storage: Preventing Flat Spots and Dry Rot
How months of sitting changes your tires — and what to do about it
EV and Hybrid Classic Car Storage: Special Considerations
What's different about storing cars with high-voltage systems